bigtwin prodgroup Tools

Jims transmission door installer tool allows installation of transmission shafts without the use of a hydraulic or arbor press. FITMENT 1982 / 199...

Jims wrist pin bushing reamer tool is easy to use with their design lead in taper at the start of each ream. Reamer is made to exact tolerance pil...

Jims transmission stud installer tool is used on stock and aftermarket transmissions that use bottom mouting studs. FITMENT 1936 / 1940 EL 1937 /...

Lower fork bearing press tube tool fits over 1 stem allowing bearing to be driven on. FITMENT 1984 / 2017 FXST 1986 / 2017 FLST 1948 / 1984 FL...

Needle bushing tool positions pinion bushing in cam cover. FITMENT 1970 / 1984 FL 1971 / 1984 FX 1982 / 1994 FXR 1982 / 1994 FXR 1979 / 1998 F...

Snap ring remover tool will remove the Timken bearing outer race snap ring without damage to the case. You can replace the snap ring in Big Twin ca...

Jims seal tool is used to install the main seal in transmission. Tool will press in the seal as flat and straig ht as possible. FITMENT 1986 / 200...

10-1/2 spoon tire iron tool FITMENT 0 / All modelsACCESSORY ITEMS41-005041-005141-0052

Jims breather ream tool repairs damaged breather gear holes. Using this tool will repair damaged breather hole to use a .030 oversize breather gea...

This accurate gauge allows the measuring of 90° when tightening head bolts. Also features torquing sequence lasered on gauge. FITMENT 1984 / 1998 ...

Jims primary locking bar tool uses to lock the primary for service work on FXD FL and FXST models. FITMENT 1941 / 1984 FL 1984 / 2006 FXST 1971...

Jims transmission cover bearing tool removes and installs bearings on 5-speed and aftermarket 6-speed transmissions. FITMENT 1982 / 1994 FXR 1982...

Jims cam bearing and bushing alignment tool checks the alignment of cam bearing to cam cover bushing. Any binding of this tool indicates misalignme...

Jims 35mm hex fork nut socket tool removes or installs the top fork nut and has a 3/8 drive. Tool has a rubber protector on the inside to prevent ...

Jims main driver tool set is used to install the main drive gear oil seal to the proper depth. Set includes a protective sleeve for seal. FITMENT ...

Jims tappet screw plug tool is used to remove tappet oil filter screen plug without removing exhaust pipes. FITMENT 1953 / 1984 FL 1971 / 1984 FX...

Jims pin gear lock tool is used when applying torque to the pinion nut. Align underneath gear and screw into case.FITMENT 1954 / 1984 FL 1971 / 19...

Cylinder head support stand. Adapters are to be used with a bar press and that is included to push guides in and out in a straight line. Set inclu...

Primary drive lock tool with step is used as a wedge type device to hold the primary drive gear while the proper torque is applied. Tool is constru...

Pinion bearing race removal tool is used to remove and install the outer race on 1958 and later models. FITMENT 1958 / 1984 FL 1971 / 1984 FX 19...

Fork tube plug socket wrench tool FITMENT 1948 / 1984 FL 1980 / 1986 FX 1986 / 2017 FLST 1979 / UP FLT ACCESSORY ITEMS41-014841-013641-0116

Piston ring installer plier tool FITMENT 0 / All modelsACCESSORY ITEMS11-021611-017616-116416-0622

Ring-o-matic ring compressor tool kit The smallest size this tool will go down to is 2-7/8 .FITMENT 0 / All modelsACCESSORY ITEMS16-052941-015141...

Multi blade groove cleaner tool FITMENT 0 / All modelsACCESSORY ITEMS16-052941-015141-0168