bigtwin prodgroup Tools

This tool is used to remove the 2-1/4 hex nut from the main drive gear which secures the rear drive trans pulley. To be used with 1/2 drive ratc...

Jims M8 FXST engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2018 / UP FLST 2018 / UP FXST...

Jims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel in the...

This Jims cylinder torque plate tool kit simulates stress conditions when boring and honing cylinders. For M8 models. FITMENT 2017 / UP FLT 2018 ...

Jims left main seal removal tool is for M8 models. FITMENT 2017 / UP FLT 2018 / UP FXST ACCESSORY ITEMS16-180341-016041-018641-0193

Jims M8 FLT engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2017 / UP FLT ACCESSORY ITEMS1...

Jims fork cap installation tool for use on 49mm forks allows the installation of the fork tube caps on the motorcycle without removing other parts...

Jims fork cap large allen head socket tool for use on 49mm forks. FITMENT 2014 / UP FLT ACCESSORY ITEMS16-052941-015141-0168

Jims steering head race installer tool features smaller and tapered drivers ensuring optimal alignment and a fully installed depth. FITMENT 2014 ...

Jims axle installation guide tool is for use on 1 or 25mm hollow axles. FITMENT 2008 / UP FLT 2008 / UP FLST 2008 / UP FXST 2008 / 2017 FXD A...

Jims FLT inner primary shifter shaft bushing tool easily removes both worn bushings and quickly installs the new bushings to the proper location at...

Jims shifter mechanism sleeve is for removing and installing the shifter mechanism sleeve in M8 transmissions. The sleeve can be removed and instal...

Jims valve spring compressor adapter for diassembly and assembly of the multiple smaller valves on M8 models. *NOTE: Conical valve spring adapter o...

Jims cylinder head holder tool is two sided one side threaded for Twin Cam heads and the other threaded for M8 models. FITMENT 1999 / UP FLT 19...

Jims wrist pin remover adapter tool quickly and easily removes the wrist pins in M8 engines. To save space in the tool box use with Jims TC-88 wri...

Jims left main bearing oil seal installer assists with perfect installation and adds the advantage of allowing the alternator stator to remain in p...

Jims balancer scissor gear alignment screw tool holds the two halves of the spring loaded scissor balancer gear in alignment before removal for eas...

This valve is used with Jims compression release valve tool. Release valve will make starting your engine effortless. Set of two. Drill and tap eac...

Use this tool for machining all Twin Cam heads for compression releases. Installs easily on front or rear head with or without valves installed. O...

The Jims piston support plate provides a non-marring flat support to push the bottom of the piston as rings and cylinder are installed over piston....

Use the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool locks into th...

Number stamp tool holds the letter or number stamps from the motor number stamp sets. FITMENT 0 / Custom applicationTECH NOTESSuggested to use w...

Jims rolling buddy engine dummy plate is to be used on all rubber mount Big Twins. This tool will allow chassis to be moved once the engine has bee...

DIY Touring tool kit for 2017 FLT models. Kit includes rider tools and service tools for the rider-mechanic. This DIY tool kit will help the rider ...