bigtwin subprodgrp Case

The Beta engine stand is powder coated steel and clears the rear balancer housing of the Beta style TC case. FITMENT 1999 / 2017 FXST 1999 / 2017...

Jims M8 FXST engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2018 / UP FLST 2018 / UP FXST...

Jims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel in the...

Jims M8 FLT engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2017 / UP FLT ACCESSORY ITEMS1...

Jims main bearing remover and installer tool removes the left and right main bearing without damaging the case it also provides correct alignment ...

Use the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool locks into th...

This flywheel truing hammer is a three pound lead/steel hammer that lasts longer than a lead hammer and is still soft enough so that it will not ma...

  This eastern bushing reaming tool is used to ream the pinion bushing in the cam cover to size. Pilots from pinion shaft case race in engine case ...

Wrist pin bushing rod clamp tool set. FITMENT 1936 / 1973 G 1936 / 1952 EL 1941 / UP FL 1941 / UP FL 1936 / 1952 W ACCESSORY ITEMS16-09539929...

Pinion puller wrench set. Factory style shop tools make the job easier!FITMENT 1936 / 1952 EL 1954 / 1992 FL 1954 / 1992 FL ACCESSORY ITEMS16-05...

Snap ring remover tool will remove the Timken bearing outer race snap ring without damage to the case. You can replace the snap ring in Big Twin ca...

Jims Timken bearing race installer tool is used when installing bearing races in the left crankcase. Use this tool to press in bearing races straig...

Jims hard cap tool protects shaft when using press. FITMENT 1955 / 1984 FL 1971 / 1984 FX 1984 / 2017 FXST 1979 / UP FLT 1979 / UP FLT 1986 /...

Truing machine features cast iron construction and is designed to true stock style flywheels. For fork tube straightness checking you must order t...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a Big Twin and T...

Connecting rod bushing tool set Replica connecting rod clamping tool piston pin bushing tool and a V-Twin motor service patch. FITMENT 0 / All ...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a TC-88 engine. ...

Left rear lower mount bolt wrench tool allows removal and installation of left rear motor mount bolt without removing the inner primary cover. FIT...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a Big Twin engin...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a standard Big T...

Cross arm puller tool is a 1 square bar 4-3/4 long and slotted with 3/8 x 16 bolts. Use any size bolt to pull gears and sprockets that have 2 ta...

Sifton 3 piece factory tool set includes a connecting rod clamping tool wrist pin bushing reamer tool and installer and the precision reamer. The...

Allows the engine builder to check flywheel run out of the pinion shaft while assembled in the engine case. Also allows the checking of gear lash o...

Tool is needed to spot face the right case so that the bolt head will seat flat on the case surface. This tool is required when any Twin Cam case s...