classic prodgroup Tools

Pinion puller wrench set. Factory style shop tools make the job easier!FITMENT 1936 / 1952 EL 1954 / 1992 FL 1954 / 1992 FL ACCESSORY ITEMS16-05...

Black oxide oil filter wrench tool is used with 3/8 drive. Tool is for easy removal and installation with spin on filters. The black oxide finish ...

Jims 4 speed clutch gear puller tool is designed to remove the starter clutch gear without damage to the gear or shaft. FITMENT 1936 / 1940 EL 19...

Jims transmission door installer tool allows installation of transmission shafts without the use of a hydraulic or arbor press. FITMENT 1982 / 199...

Jims transmission stud installer tool is used on stock and aftermarket transmissions that use bottom mouting studs. FITMENT 1936 / 1940 EL 1937 /...

Lower fork bearing press tube tool fits over 1 stem allowing bearing to be driven on. FITMENT 1984 / 2017 FXST 1986 / 2017 FLST 1948 / 1984 FL...

Needle bushing tool positions pinion bushing in cam cover. FITMENT 1970 / 1984 FL 1971 / 1984 FX 1982 / 1994 FXR 1982 / 1994 FXR 1979 / 1998 F...

Main shaft starter clutch puller tool FITMENT 1936 / 1940 EL 1941 / 1984 FL 1937 / 1948 UL 1971 / 1984 FX ACCESSORY ITEMS41-016841-016041-0186...

10-1/2 spoon tire iron tool FITMENT 0 / All modelsACCESSORY ITEMS41-005041-005141-0052

Jims breather ream tool repairs damaged breather gear holes. Using this tool will repair damaged breather hole to use a .030 oversize breather gea...

Jims primary locking bar tool is used to lock the primary for service work on FXR FLT and FLHT models. FITMENT 1979 / UP FLT 1982 / 1994 FXR 19...

Jims primary locking bar tool uses to lock the primary for service work on FXD FL and FXST models. FITMENT 1941 / 1984 FL 1984 / 2006 FXST 1971...

Jims transmission cover bearing tool removes and installs bearings on 5-speed and aftermarket 6-speed transmissions. FITMENT 1982 / 1994 FXR 1982...

Jims cam bearing and bushing alignment tool checks the alignment of cam bearing to cam cover bushing. Any binding of this tool indicates misalignme...

Jims 35mm hex fork nut socket tool removes or installs the top fork nut and has a 3/8 drive. Tool has a rubber protector on the inside to prevent ...

Jims Timken bearing race installer tool is used when installing bearing races in the left crankcase. Use this tool to press in bearing races straig...

Jims cam cover bushing remover tool will remove the cam cover bushing and will also remove cam bushing in case. This tool is sturdy reliable and i...

Jims hard cap tool protects shaft when using press. FITMENT 1955 / 1984 FL 1971 / 1984 FX 1984 / 2017 FXST 1979 / UP FLT 1979 / UP FLT 1986 /...

Jims main driver tool set is used to install the main drive gear oil seal to the proper depth. Set includes a protective sleeve for seal. FITMENT ...

Jims tappet screw plug tool is used to remove tappet oil filter screen plug without removing exhaust pipes. FITMENT 1953 / 1984 FL 1971 / 1984 FX...

Jims cam bearing installer tool presses the inner cam bearings smoothly into the right case with the bearings installed to the proper depth. FITME...

Jims pin gear lock tool is used when applying torque to the pinion nut. Align underneath gear and screw into case.FITMENT 1954 / 1984 FL 1971 / 19...

Jims wheel hub nut wrench tool is used to remove and install the slotted locknut to the correct torque on the spoke wheel. FITMENT 1967 / 1972 FL ...

Cylinder head support stand. Adapters are to be used with a bar press and that is included to push guides in and out in a straight line. Set inclu...