prodgroup Tools

Rider tool kit fits into the included 7 x 2 blue zip-up pouch. 17 piece tool kit. NOTE: Entire kit will fit in oval kidney shaped tool boxes.FITM...

Hardened steel stamps to restore motor numbers on early motors. Sold as a 22 piece set.FITMENT 1948 / 1969 FL 1948 / 1952 EL TECH NOTESSuggested ...

Set includes a special tap tool used for repairing or is used for repairing or dressing 1/4 x 24 TPI and the corresponding tap tool. FITMENT 1941...

This tool is used to remove the 2-1/4 hex nut from the main drive gear which secures the rear drive trans pulley. To be used with 1/2 drive ratc...

Jims M8 FXST engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2018 / UP FLST 2018 / UP FXST...

Jims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel in the...

Jims primary locking bar tool locks the primary drive on XL models to facilitate crankshaft sprocket nut removal and installation along with clutc...

This Jims cylinder torque plate tool kit simulates stress conditions when boring and honing cylinders. For M8 models. FITMENT 2017 / UP FLT 2018 ...

Jims left main seal removal tool is for M8 models. FITMENT 2017 / UP FLT 2018 / UP FXST ACCESSORY ITEMS16-180341-016041-018641-0193

Jims M8 FLT engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2017 / UP FLT ACCESSORY ITEMS1...

Jims fork cap installation tool for use on 49mm forks allows the installation of the fork tube caps on the motorcycle without removing other parts...

Jims fork cap large allen head socket tool for use on 49mm forks. FITMENT 2014 / UP FLT ACCESSORY ITEMS16-052941-015141-0168

Jims steering head race installer tool features smaller and tapered drivers ensuring optimal alignment and a fully installed depth. FITMENT 2014 ...

Jims axle installation guide tool is for use on 1 or 25mm hollow axles. FITMENT 2008 / UP FLT 2008 / UP FLST 2008 / UP FXST 2008 / 2017 FXD A...

Jims swingarm bearing installer tool can be used on both the drive side and brake side bearings which are at diffent depths for easy and accurate...

Jims FLT inner primary shifter shaft bushing tool easily removes both worn bushings and quickly installs the new bushings to the proper location at...

Jims XL sprocket nut socket is designed specifically for XL models to remove install and properly tighten the front final drive sprocket/pulley. ...

Jims shifter mechanism sleeve is for removing and installing the shifter mechanism sleeve in M8 transmissions. The sleeve can be removed and instal...

Essential for installation of the countershaft 1st scissor gear this tool ensure that the scissor gear teeth mesh correctly with the mainshaft 1st...

Jims valve spring compressor adapter for diassembly and assembly of the multiple smaller valves on M8 models. *NOTE: Conical valve spring adapter o...

Jims cylinder head holder tool is two sided one side threaded for Twin Cam heads and the other threaded for M8 models. FITMENT 1999 / UP FLT 19...

Jims wrist pin remover adapter tool quickly and easily removes the wrist pins in M8 engines. To save space in the tool box use with Jims TC-88 wri...

Jims cylinder hold down nuts keep the cylinders in place when the heads are removed from the engine. Useful when installing the second cylinder ove...

Jims camshaft needle bearing remover and installer tool is required for correct and accurate replacement of the camshaft inner needle bearing for M...