subprodgrp Case

The Beta engine stand is powder coated steel and clears the rear balancer housing of the Beta style TC case. FITMENT 1999 / 2017 FXST 1999 / 2017...

Jims M8 FXST engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2018 / UP FLST 2018 / UP FXST...

Jims M8 flywheel locking tool has an added o-ring to prevent oil seepage. This tool is designed to specifically locate and lock the flywheel in the...

Jims M8 FLT engine stand needed for any powertrain work is built from .125 steel and powdercoated blue. FITMENT 2017 / UP FLT ACCESSORY ITEMS1...

Jims XL sprocket nut socket is designed specifically for XL models to remove install and properly tighten the front final drive sprocket/pulley. ...

Jims main bearing remover and installer tool removes the left and right main bearing without damaging the case it also provides correct alignment ...

Use the balancer shaft retention pin tool secures the engine balancers on TC-88B engines when servicing flywheel assembl y. This tool locks into th...

Our crankshaft locking tool fits 1991-1999 XL models by engaging the pinion shaft splines. This allows removal and torquing of the pinion nut durin...

This flywheel truing hammer is a three pound lead/steel hammer that lasts longer than a lead hammer and is still soft enough so that it will not ma...

  This eastern bushing reaming tool is used to ream the pinion bushing in the cam cover to size. Pilots from pinion shaft case race in engine case ...

This eastern bushing reaming tool fits pinion bushing in cam cover. FITMENT 1957 / 1976 XL 1954 / 1956 K MEASURMENTSReam Diameter: 5/8 inchesPil...

This eastern bushing reaming tool fits pinion bushing in cam cover. FITMENT 1977 / 1985 XL ACCESSORY ITEMS16-052941-015141-0168

This eastern bushing reaming tool fits pinion bushing in cam cover. FITMENT 1955 / 1957 FL ACCESSORY ITEMS16-052941-015141-0168

This eastern bushing reamer fits pinion bushing in cam cover . Includes pilot bushing.FITMENT 1941 / 1954 FL ACCESSORY ITEMS16-052941-015141-0168

Case lap head only has an outer diameter of 1-3/4 . FITMENT 0 / All modelsACCESSORY ITEMS16-052941-015141-0168

Sprocket shaft seal wrench tool installs and removes bearing nut on Big Twin models. FITMENT 1955 / 1969 FL ACCESSORY ITEMS16-052941-016841-0151

Wrist pin bushing rod clamp tool set. FITMENT 1936 / 1973 G 1936 / 1952 EL 1941 / UP FL 1941 / UP FL 1936 / 1952 W ACCESSORY ITEMS16-09539929...

Pinion puller wrench set. Factory style shop tools make the job easier!FITMENT 1936 / 1952 EL 1954 / 1992 FL 1954 / 1992 FL ACCESSORY ITEMS16-05...

Snap ring remover tool will remove the Timken bearing outer race snap ring without damage to the case. You can replace the snap ring in Big Twin ca...

Jims Timken bearing race installer tool is used when installing bearing races in the left crankcase. Use this tool to press in bearing races straig...

Jims hard cap tool protects shaft when using press. FITMENT 1955 / 1984 FL 1971 / 1984 FX 1984 / 2017 FXST 1979 / UP FLT 1979 / UP FLT 1986 /...

Jims sprocket shaft seal installer tool is designed to install sprocket shaft seal to proper depth and for holding the seal perfectly square for a ...

Truing machine features cast iron construction and is designed to true stock style flywheels. For fork tube straightness checking you must order t...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a Big Twin and T...