subprodgrp Case

Connecting rod bushing tool set Replica connecting rod clamping tool piston pin bushing tool and a V-Twin motor service patch. FITMENT 0 / All ...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a TC-88 engine. ...

Left rear lower mount bolt wrench tool allows removal and installation of left rear motor mount bolt without removing the inner primary cover. FIT...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a Big Twin engin...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use on Ironheads and E...

Engine stand is to be used with an auto engine stand which is not included allowing the auto engine stand to be adapted to use for a standard Big T...

Cross arm puller tool is a 1 square bar 4-3/4 long and slotted with 3/8 x 16 bolts. Use any size bolt to pull gears and sprockets that have 2 ta...

Sifton 3 piece factory tool set includes a connecting rod clamping tool wrist pin bushing reamer tool and installer and the precision reamer. The...

Allows the engine builder to check flywheel run out of the pinion shaft while assembled in the engine case. Also allows the checking of gear lash o...

Tool is needed to spot face the right case so that the bolt head will seat flat on the case surface. This tool is required when any Twin Cam case s...

Required when any Twin Cam case cylinder spigot hole is enlarged for Big Bore cylinders. FITMENT 1999 / 2017 FXST 1999 / 2017 FLST 1999 / 2016 F...

Jims flywheel truing tool is to tune flywheel assemblies when truing. This tool features both a flywheel expander and contractor in one easy to use...

Sprocket shaft bearing nut wrench tool installs nut and seal. FITMENT 1955 / 1969 FL ACCESSORY ITEMS16-013816-0140

This sprocket shaft turning tool fits taper on assembled motor and allows engine to be turned over by 1/2 ratchet or impact driver. FITMENT 1930 ...

Outer race press tool is used to remove and install bearing outer race. FITMENT 1955 / 1984 FL 1971 / 1984 FX 1984 / 1998 FXST 1979 / 1998 FLT ...

Crankcase main bearing lap tool is used to lap right and left crankcase races for oversized bearings. Crankcase lapping tools developed by Gil May ...

End play gauge tool. FITMENT 1930 / 1934 VL 1937 / 1948 UL 1941 / 1954 FL 1936 / 1940 EL ACCESSORY ITEMS16-052941-015141-0168

Driver tool handle only for sprocket shaft bearing tool. For wheel and sprocket shaft races. For use with split bearing race extractor/installers.F...

Sprocket shaft bearing tool removes and installs engine sprocket shaft bearings from crankcase. Tool is a 2 part set. Sold as a 4 piece set.FITMENT...

Bearing race press plug tool is used to remove and install Timken bearing outer race. FITMENT 1977 / 2003 XL ACCESSORY ITEMS16-052941-016841-0151

Bearing race press plug tool is used to remove and install Timken bearing outer race. FITMENT 1957 / 1976 XL ACCESSORY ITEMS16-052941-016841-0151

This combo lapping tool is used for precision alignment of engine and transmission shafts. Combo lapping tool is used to lap right and left crankca...

Replacement lap head tool for engine 1.750 are sold by the each and for Eastern tool only. FITMENT 0 / Replacement applicationACCESSORY ITEMS...

Replica connecting rod clamping tool FITMENT 0 / All modelsTECH NOTESAllows rod to be held for straightening or to replace wrist pin bushingACCE...