subprodgrp Tools

Chain puller tool. FITMENT 0 / All ACCESSORY ITEMS16-025516-172916-061116-0144

Set includes hex wrench tool and 18mm spark plug socket. For use with 1-5/32 OEM style spark plugs only. Order rivet set tool separately.FITMENT 1...

Clutch compression tool has adapter included FITMENT 1990 / UP FLT 1991 / 2017 FXD 1990 / 2017 FXST 1990 / 2017 FLST 1991 / UP XL 1990 / 1994...

Oxygen sensor fitting tread chasers are used to repair damaged sensor threaded bungs in exhaust pipes. For use with 18mm sensors and can be used wi...

This tool removes the starter ring gear rivets from clutch shells. FITMENT 1990 / 2006 FXST 1990 / 2006 FLST 1990 / 2006 FLT 1991 / 2005 FXD A...

The Jims primary locking tool is used to lock the clutch hub sprocket to the front engine sprocket. It also allows the removal or torquing of clutc...

Wrench is for 18mm early style air cooled 7/8 and 1-1/8 Champion hex plugs. Wrench fits new type Champion spark plug D-16.FITMENT 1937 / 1939 WL ...

V-Twin ignition switch tool allows quick and easy alignment of the ignition switch cover and housing while the retaining screws are being torqued! ...

Receptacle extractor tool removes Molex style connector FITMENT 0 / All Big Twin models0 / All XL modelsACCESSORY ITEMS60-016460-0170

Jims primary locking bar tool locks the primary drive on XL models to facilitate crankshaft sprocket nut removal and installation along with clutc...

Jims swingarm bearing installer tool can be used on both the drive side and brake side bearings which are at diffent depths for easy and accurate...

Jims FLT inner primary shifter shaft bushing tool easily removes both worn bushings and quickly installs the new bushings to the proper location at...

Jims high output alternator rotor remover and installer easily removes the rotor while protecting the magnets within it. For use on M8 models. FIT...

Used to make installing or removing the ignition switch and fork lock a easy process. Locates on the ignition switch face nut that holds the switch...

The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 3/8 drive ratchet. For use on O2 sensors that have 1...

The oxygen sensor tool easily removes or installs sensors on fuel injected models. Use with a 7/8 wrench or a 3/8 drive ratchet. For use on O2 se...

Rod alignment plate features a cast iron construction with a parkerized finish for Big Twin engines. FITMENT 1936 / 1952 EL 1941 / 1985 FL ACCE...

Our Big Twin alternator rotor puller uses the sprocket shaft end to center the two threaded holes in the rotor to allow its safe removal. *NOTE: Fo...

Jims clutch adjusting tool for use on Big Twins 1985-up allows the mechanic to quickly and accurately tighten the clutch adjusting screw jam nut wi...

This tool safely removes and installs the inner primary bearing without damage to the new bearing. Also removes and installs inner primary and seal...

This wheel lug wrench tool has a 3/8 hex key shaft and is sold each. FITMENT 1982 / UP FLT ACCESSORY ITEMS41-019416-0529

This clutch drum locking tool is for removing the clutch hub and motor nuts without problems. FITMENT 1971 / 1984 XL ACCESSORY ITEMS41-016841-016...

Primary plug wrench FITMENT 1971 / 1984 XL ACCESSORY ITEMS41-016841-016041-018641-0193

The clutch compressor tool easily allows disassembly of the clutch pack FITMENT 1990 / 2017 FXST 1990 / 2017 FLST 1990 / UP FLT 1990 / 1994 FXR...